Festo 4080491 CPX-E-8DO Digital Output Module, 8 PNP Channels

USD 1,120.86

Eight-channel PNP output module for CPX-E with 24 V DC load supply, spring terminals, per-channel electronic fuses, bus/LED diagnostics and DIN-rail mounting.

Festo Remote I/O and Network Interface Components

Festo CPX-E-8DO Digital Output Module

BrandFesto
Model IdentifierCPX-E-8DO
Official Part Number4080491

Technical Overview

The Festo CPX-E-8DO adds eight positive-switching digital outputs to a compatible CPX-E automation system. The outputs follow IEC 61131-2 type 0.5 characteristics and use a nominal 24 V DC load supply with ±25% permissible voltage fluctuation. Four spring-terminal strips provide two outputs each, while a separate terminal strip supplies the load circuit. Electronic fuse protection acts per channel, and bus plus LED diagnostics identify module, channel, short-circuit/overload and load-undervoltage conditions. Channel-to-internal-bus isolation is provided, without channel-to-channel isolation. The 93 g PA module mounts on a DIN rail and provides IP20 protection, with a 30 m maximum output cable length.

Eight-channel CPX-E PNP digital output module with 24 V DC load supply, spring terminals, per-channel electronic fuses and IP20 protection.

Key Features

  • Eight PNP positive-switching digital outputs
  • One-byte output address capacity
  • Output characteristics to IEC 61131-2, type 0.5
  • Nominal 24 V DC load supply with ±25% voltage tolerance
  • Four spring-terminal output strips with two outputs each
  • Internal electronic short-circuit fuse per channel
  • Bus diagnostics for module error, output short circuit/overload and load undervoltage
  • LED module/channel fault indication and channel-state indication
  • Isolation between channels and internal bus; no channel-to-channel isolation
  • 93 g DIN-rail PA module, IP20, with 30 m maximum output cable length

Connect eight compatible 24 V DC electrical loads to CPX-E with per-channel electronic protection and local plus bus diagnostics.

Technical Specification Matrix

ParameterValue
Mounting grid pitch18.9 mm
Type of mountingvia DIN rail
Physical Weight (kg)0.093
Mounting positionVertical; Horizontal
Ambient temperature-5 °C...50 °C
Note on ambient temperature-5 - 60°C for vertical installation
Storage temperature-20 °C...70 °C
Relative air humidity95%; Non-condensing
Degree of protectionIP20
Corrosion resistance class CRC0 - No corrosion stress
Vibration resistanceTransport application test with severity level 1 to FN 942017-4 and EN; 60068-2-6
Shock resistanceShock test with severity level 1 to FN 942017-5 and EN 60068-2-27
Protection against direct and indirect contactPELV
Max. cable length30 m outputs
LABS (PWIS) conformityVDMA24364 zone III
CE mark (see declaration of conformity)To EU EMC Directive; In accordance with EU RoHS Directive
UKCA marking (see declaration of conformity)To UK instructions for EMC; To UK RoHS instructions
KC markKC-EMV
ApprovalRCM; c UL us - Listed (Oil)
Certificate issuing authorityUL E239998
Note on materialsRoHS compliant
Material housingPA
Diagnostics via LEDError per channel; Errors per module; Status per channel
Diagnostics via busModule error; Short circuit/overload at output; Load supply undervoltage
Max. address volume, outputs1 Byte
Number of outputs8
Module parametersShort circuit diagnostics at output; Diagnostics for undervoltage in load supply; Behaviour after short circuit/overload
Channel parametersForce channel x
Power supply, connection typeTerminal strip
power supply, connection systemSpring-loaded terminal
Power supply, number of pins/wires4
Nominal operating voltage DC of load24 V
Permissible voltage fluctuation of load±25%
Power supply, conductor diameter0.2 mm²...1.5 mm²
Power supply, note on conductor diameter0.2 - 2.5 mm² for flexible conductors without wire ferrule
Intrinsic current consumption at nominal operating voltage loadTypically 34 mA
Reverse polarity protection24 V load against 0 V load
Electrical connection output, functionDigital output
Electrical connection output, connection type4x terminal strip
Electrical connection output, connector systemSpring-loaded terminal
Electrical connection output, number of connections/cores4
Electrical connection for output, conductor cross section0.2 mm²...1.5 mm²
Electrical connection for output, note on conductor cross section0.2 - 2.5 mm² for flexible conductors without wire ferrule
Characteristic for outputsTo IEC 61131-2, type 0.5
Switching logic for outputsPNP (positive switching)
Behaviour after end of overload of the outputsNo automatic return (default); Parameterisable (module by module)
Max. residual current outputs per module4 A
Isolation channel - channelNo
Isolation channel - internal busYes
Fuse protection (short circuit)Internal electronic fuse per channel
Dimensions L x W x H (cm)7.66 x 1.89 x 12.43

Industrial Applications

1. Electrical Commands for Pneumatic Valve Coils

A CPX-E-controlled machine needs discrete electrical commands for compatible 24 V DC valve coils. The module provides eight positive-switching outputs through spring-terminal strips and occupies one output-data byte. Per-channel electronic fuses and output short-circuit/overload diagnostics provide defined protection and fault information for integrating those coil circuits into the automation system.

Problem Solved

Eight digital channels translate the CPX-E control sequence into individual electrical valve commands, while channel protection and diagnostics help identify a faulted output circuit.

8 PNP outputs 24 V DC load Electronic channel fuses

2. Switching Contactor Coils in an Assembly Cabinet

An assembly cabinet uses contactor coils as the electrical command interfaces for selected loads. The manufacturer lists contactors among compatible consumer types for the digital output module, subject to the IEC 61131-2 type 0.5 output characteristics. A separate load-supply terminal and bus-isolated output circuitry define the module-level electrical arrangement for those control circuits.

Problem Solved

Positive-switching outputs provide discrete contactor commands within the stated output characteristics, giving the cabinet controller individual load-control channels with module and channel diagnostic information.

IEC 61131-2 type 0.5 Spring terminals Bus isolation

3. Driving Machine Status Indicators

A machine needs separate visual indicators for operating states communicated by its CPX-E controller. The output module can switch compatible 24 V DC display components, using eight PNP channels and spring-terminal connections. Per-channel state LEDs support local observation, while load-supply undervoltage and output faults are available through bus diagnostics when the indicated state does not match the intended command.

Problem Solved

Discrete outputs provide independent commands for machine indicators, and the accompanying state and fault information helps distinguish a controller command from an electrical output-circuit problem.

8 digital channels LED diagnostics 24 V DC
Select your currency