SICK 1048048 MZT8-28VPS-KP0 PNP Magnetic Cylinder Sensor

USD 49.14

MZT8-28VPS-KP0 detects a cylinder magnet with a PNP normally-open output, typical 9 mm overrun, a 0.3 m PUR M8 pigtail and IP68 PA12 housing.

SKU SICK-1048048 Category
SICK MZT8

SICK MZT8-28VPS-KP0 PNP Magnetic Cylinder Sensor

BrandSICK
Model IdentifierMZT8-28VPS-KP0
Official Part Number1048048

Technical Overview

The SICK MZT8-28VPS-KP0 is a magnetic cylinder sensor for T-slots, providing a PNP normally-open output through DC three-wire wiring. It has a 24 mm housing, typical response sensitivity of 2.8 mT and typical 9 mm overrun distance, representing magnet travel while a switching signal is output. The device supports 1,000 Hz switching and operates from 10–30 V DC, with 10 mA consumption without load and continuous output current no greater than 200 mA. An axial 0.3 m PUR cable ends in an M8 three-pin connector and has documented drag-chain and torsion capabilities. The PA12 housing provides IP68 protection, an LED indicates switching status, and operating temperature spans −30 to +80 °C.

T-slot magnetic cylinder sensor with PNP normally-open output, typical 9 mm overrun, 0.3 m PUR cable and M8 three-pin connector.

Key Features

  • T-slot magnetic cylinder sensor with 24 mm housing
  • PNP normally-open output; DC three-wire connection; 1,000 Hz switching
  • Typical 2.8 mT sensitivity, 9 mm overrun distance and 0.7 mT hysteresis
  • Reproducibility ≤0.1 mT at specified supply and constant ambient temperature
  • 10–30 V DC; 10 mA without load; output current ≤200 mA
  • Axial 0.3 m PUR pigtail with M8 three-pin connector
  • Cable torsion ±270° per 10 cm; >2 million torsion and drag-chain cycles
  • PA12 housing; IP68 to EN 60529, with IP67/IP68 footnote
  • Reverse-polarity, short-circuit and power-up pulse protection; LED indicator
  • −30 to +80 °C operation; fixing screw SW2.0 with typical 0.4 Nm torque

Detect the cylinder magnet through a T-slot-mounted sensor and send a PNP normally-open position condition to external machine sequencing.

Technical Specification Matrix

ParameterValue
Functional principleMagnetic cylinder-position detection
Cylinder typeT-slot
Cylinder types with adapterProfile, tie-rod, round-body and dovetail-groove cylinders; SMC CDQ2 and ECDQ2 rails; suitable adapter required
Housing length24 mm
Switching outputPNP; normally open
Electrical wiringDC three-wire
Switching frequency1,000 Hz
Response sensitivityTypical 2.8 mT
Overrun distanceTypical 9 mm; distance traveled by the magnet while the sensor outputs a switching signal; switching-point width plus hysteresis
HysteresisTypical 0.7 mT
Reproducibility≤0.1 mT at supply voltage UB and constant ambient temperature Ta
Power supply10–30 V DC
Current consumption10 mA without load
Voltage drop≤2.2 V
Continuous output current≤200 mA
Time delay before availability25 ms
Protection classIII
Reverse polarity protectionYes
Short-circuit protectionYes
Power-up pulse protectionYes
Teach-inNo
IndicatorSwitching-status LED
Connection0.3 m PUR cable with M8 three-pin connector; drag-chain use
Cable outletAxial
Conductor cross-section0.14 mm²
Cable diameter2.9 mm
Minimum bending radiusFixed installation >3 × cable diameter; flexible use >10 × cable diameter
Cable torsion±270° per 10 cm
Torsion cycles>2,000,000
Drag-chain cycles>2,000,000
Drag-chain parametersMaximum traversing speed 3.3 m/s at 5 m horizontal traversing length; maximum acceleration 5 m/s²
Pin assignmentCD-002: 1 BN=L+; 4 BK=normally-open output; 3 BU=M
Fixing screwSW2.0; typical tightening torque 0.4 Nm
Housing materialPA12 plastic
IP ratingIP68; EN 60529 footnote identifies IP67/IP68
Operating temperature−30 to +80 °C
Shock resistance30 g, 11 ms
Vibration resistance10–55 Hz, 1 mm
EMCEN 60947-5-2
UL fileNRKH.E181493 and NRKH7.E181493
MTTFD2,289 years
DCavg0%
Mission time20 years

Industrial Applications

1. Confirming an extended clamp position

A pneumatic clamp can mount the sensor in its cylinder T-slot at the expected extended piston position. The cylinder magnet actuates the PNP normally-open output when it enters the sensing region. External sequencing logic reads that condition after the stroke, with installation accounting for the typical 9 mm overrun and magnetic sensitivity. The LED assists locating the switching region during mechanical setup.

Problem Solved

A magnetic position condition helps external sequencing logic distinguish the expected extended clamp presentation from an incomplete stroke, supporting the next machine step after the cylinder reaches its reference region.

Clamp extension PNP normally open T-slot mounting

2. Detecting a delayed return stroke

A handling cylinder can position the sensor at its expected retracted reference and send the output to an external controller timer. After commanding return, the controller measures the interval until that reference condition appears and compares it with a configured machine timeout. The 0.3 m M8 pigtail and documented cable movement capabilities support connection on a moving assembly within their specified limits.

Problem Solved

A return-position signal gives external timing logic a defined event for detecting delayed cylinder movement, helping identify a stroke that fails to reach its expected reference on time.

Return timing External timeout M8 pigtail

3. Counting completed cylinder cycles

A repetitive handling station can count a selected reference-position event as the cylinder completes each defined motion cycle. External cycle logic qualifies the PNP transition with the commanded sequence so repeated sampling of one position does not create extra counts. Magnetic detection avoids a mechanical feeler at the piston, while the fixing screw secures the sensor in the adjusted T-slot location.

Problem Solved

Qualified reference-position events let external production logic count completed cylinder cycles, providing a movement-based record for machine usage and maintenance intervals instead of counting commands alone.

Cycle count Qualified position event Mechanical fixing
Select your currency