SICK 6026473 IQ80-50BPP-KC0 Inductive Sensor

USD 165.88

Rectangular inductive sensor with 50 mm nominal range, complementary PNP outputs, M12 connector, 70 Hz switching and IP67 protection.

SKU SICK-6026473 Category
SICK IQL

SICK IQ80-50BPP-KC0 Inductive Proximity Sensor

BrandSICK
Model IdentifierIQ80-50BPP-KC0
Official Part Number6026473

Technical Overview

The SICK IQ80-50BPP-KC0 is a rectangular inductive proximity sensor with a 50 mm nominal range for detecting metal targets without contact. It provides complementary PNP outputs, with a switching frequency of 70 Hz. This version supports flush, non-flush and overflush installation, and connects through an M12 four-pin male connector. Its zinc-diecast housing and PPE sensing face have IP67 protection. A 10–36 V DC supply and output current up to 250 mA support connection to compatible machine controls. Target material reduction factors and the manufacturer mounting clearances determine the final detection arrangement.

Rectangular 50 mm inductive metal sensor with complementary PNP outputs, 70 Hz switching and M12 four-pin connection.

Key Features

  • 50 mm nominal inductive metal-detection range
  • Flush, non-flush and overflush installation
  • Complementary PNP NO/NC outputs; DC four-wire
  • 70 Hz switching frequency
  • 10–36 V DC; continuous output current ≤250 mA
  • M12 four-pin male connector
  • Zinc-diecast housing; PPE sensing face
  • IP67 per EN 60529
  • −25 to +70 °C operation
  • Short-circuit protection

Detect metal machine targets at a 50 mm nominal distance with complementary PNP signals and three supported mounting arrangements.

Technical Specification Matrix

ParameterValue
Functional principleInductive metal proximity detection
Housing formRectangular, standard design
Sensing range Sn50 mm nominal
InstallationFlush, non-flush or overflush
Switching frequency70 Hz
Output configurationComplementary PNP NO and NC
Electrical wiringDC four-wire
ConnectionM12 four-pin male connector
Connection diagramCD-009
Power supply10–36 V DC
Voltage drop≤2.5 V at maximum output current and 24 V supply
Hysteresis3–20%
Temperature drift±15% of Sr
EMCAccording to EN 60947-5-2
Operating temperature−25 to +70 °C
Housing materialZinc diecast, GD Zn
Sensing face materialPPE plastic
Shock resistance30 g, 11 ms
Vibration resistance10–55 Hz, 1 mm
IP ratingIP67 per EN 60529
MTTFD1,859 years
Diagnostic coverage DCavg0%
Mission time20 years
Target-material reduction factorsApproximate reference values, may vary: V2A/304=0.85; aluminum=0.46; copper=0.38; brass=0.48
Mounting clearancesA=0 mm; B=80 mm; C=80 mm; D=150 mm; E=0 mm; F=400 mm; follow exact installation diagram
Pin assignment1/BN: L+; 4/BK: NO; 3/BU: M; 2/WH: NC
Continuous output current≤250 mA
Circuit protectionShort-circuit protection
Mounting hole pitch65 ×65 mm
Mounting holesØ5.5 mm

Industrial Applications

1. Confirming a metal pallet at a transfer stop

A transfer stop can position a qualified metal pallet feature in front of the sensing face. The 50 mm nominal range permits a detection gap subject to target material and the required installation clearances. The external controller evaluates the selected output state as a local pallet-position reference before it advances the transfer sequence.

Problem Solved

A noncontact arrival signal provides the transfer controller with a pallet-position input, avoiding a mechanical lever contacting the pallet during repeated station-to-station handling cycles.

Pallet position 50 mm nominal Inductive

2. Checking a metal assembly at a fixture

An assembly fixture can bring an intended metal component into the sensor detection zone at a defined inspection point. The output reports the local presence condition, while the documented material reduction factors guide qualification of stainless steel, aluminum, copper or brass targets. The 70 Hz switching frequency defines the available event rate for the fixture sequence.

Problem Solved

A metal-presence condition lets the external controller flag an empty monitored fixture position before the next operation, without depending on a visible contrast mark on the component.

Fixture presence Material factors 70 Hz

3. Counting spaced metal carriers on a conveyor

A conveyor can pass separated metal carrier features across the sensing zone and send the resulting output transitions to an external counter. Carriers must be spaced so their event rate remains within the 70 Hz switching specification. The selected NO or NC transition and the mounting clearances are incorporated into the counter and conveyor setup.

Problem Solved

A qualified carrier-passage event supports throughput tracking without a contact counting arm, while the external control program performs counting and coordinates feed according to the machine sequence.

Carrier counting 70 Hz External counter
Select your currency