Connection side	field side
Connection	terminals 1+, 2-, 3 or 5-, 6+
Input signal	0/4 … 20 mA
Open circuit voltage/short-circuit current	terminals 1+, 3-: 22.7 V / 38 mA
Voltage drop	terminals 5, 6 : ≤ 2.4 V at 20 mA
Input resistance	terminals 2-, 3: max. 76 Ω terminals 1+, 3: max. 500 Ω (250 Ω load)
Available voltage	terminals 1+, 3: ≥ 16 V at 20 mA

Output

Connection side	control side
Connection	terminals 7-, 8+,9; 10-, 11+,12
Load	0 … 550 Ω at 20 mA
Output signal	0/4 … 20 mA (overload > 25 mA)
Ripple	max. 50 µA _rms

Transfer characteristics

Deviation

at 20 °C (68 °F), 0/4 … 20 mA
≤ 10 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage

Influence of ambient temperature

0.25 µA/K

Frequency range

field side into the control side: bandwidth with 0.5 V_pp signal 0 … 7.5 kHz (-3 dB)
control side into the field side: bandwidth with 0.5 V_pp signal 0.3 … 7.5 kHz (-3 dB)

Settling time

200 µs

Rise time/fall time

20 µs

Galvanic isolation

Output/power supply	functional insulation, rated insulation voltage 50 V AC
Output/Output	functional insulation, rated insulation voltage 50 V AC

Indicators/settings

Display elements	LED
Labeling	space for labeling at the front

Directive conformity

Electromagnetic compatibility

Directive 2014/30/EU

EN 61326-1:2013 (industrial locations)

Conformity

Electromagnetic compatibility	NE 21:2011
Degree of protection	IEC 60529:2001
Protection against electrical shock	UL 61010-1:2012

Ambient conditions

Ambient temperature

-20 … 60 °C (-4 … 140 °F)

Mechanical Specifications

Degree of protection

IP20

Connection

screw terminals

Mass

approx. 200 g

Dimensions

20 x 124 x 115 mm (0.8 x 4.9 x 4.5 inch) , (W x H x D) housing type B2

Height	124 mm
Width	20 mm
Depth	115 mm

Mounting

on 35 mm DIN mounting rail acc. to EN 60715:2001

Data for application in connection with hazardous areas

EU-type examination certificate

BAS 99 ATEX 7060 X

Marking	II (1)G [Ex ia Ga] IIC , [exsign] II (1)D [Ex ia Da] IIIC , [exsign] I (M1) [Ex ia Ma] I
Input	[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I

Supply

Maximum safe voltage

U_m

250 V (Attention! The rated voltage can be lower.)

Equipment

terminals 1+, 3-

Voltage	U_o	25.4 V
Current	I_o	86.8 mA
Power	P_o	551 mW
Internal capacitance	C_i	12 nF
Internal inductance	L_i	0 mH

Equipment

terminals 2-, 3

Current	I_o/Strom I_i	74 mA / 115 mA
Current	I_i	115 mA
Voltage	U_o	3.5 V
Current	I_o	74 mA
Power	P_o	64 mW

Equipment

terminals 1+, 2 / 3-

Voltage	U_i	30 V
Current	I_i	115 mA
Voltage	U_o	25.4 V
Current	I_o	115 mA
Power	P_o	584 mW

Equipment

terminals 5-, 6+

Voltage	U_i	30 V
Current	I_i	115 mA
Voltage	U_o	8.7 V
Current	I_o	0 mA

Output

Maximum safe voltage

U_m

250 V (Attention! The rated voltage can be lower.)

Certificate

TÜV 99 ATEX 1499 X

Marking

II 3G Ex nA II T4 [device in zone 2]

Galvanic isolation

Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V

Directive conformity

Directive 2014/34/EU

EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010

International approvals

UL approval

Control drawing

116-0428 (cULus)

IECEx approval

IECEx certificate	IECEx BAS 04.0016X IECEx CML 15.0055X
IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex nA IIC T4 Gc

General information

Note	Both output loads must be connected to ensure complete and correct operation within the technical specification. Open circuit of one of the two outputs will not affect the connected output, but would result in a loss of transmitter supply voltage of up to 0.7 Volt.
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.