SICK 1057030 MZT8-28VPS-KWB PNP NO T-Slot Cylinder Sensor

USD 61.88

T-slot cylinder sensor with PNP normally-open output, typical 9 mm overrun, 5 m three-wire PVC cable and IP67/IP69K protection in a 24 mm PA12 body.

SKU SICK-1057030 Category
SICK MZT8

SICK MZT8-28VPS-KWB PNP NO T-Slot Cylinder Sensor

BrandSICK
Model IdentifierMZT8-28VPS-KWB
Official Part Number1057030

Technical Overview

The SICK MZT8-28VPS-KWB is a magnetic cylinder sensor for T-slots with a PNP normally-open output and 1,000 Hz switching rating. Its long-overrun configuration specifies a typical 9 mm overrun distance and typical response sensitivity of 2.8 mT. The 24 mm PA12 housing carries an LED indicator and an SW2.0 fixing screw with a typical 0.4 Nm tightening torque. An axial 5 m three-wire PVC cable ends in ferrules for electrical connection. Operation uses 10–30 V DC, with reverse-polarity, short-circuit and power-up pulse protection. IP67/IP69K protection and −30 to +80 °C operation support cylinder installation, while adapters extend mounting to the listed additional cylinder types.

T-slot magnetic cylinder sensor with PNP normally-open output, typical 9 mm overrun, 1,000 Hz switching and a 5 m PVC cable.

Key Features

  • T-slot magnetic cylinder sensor; 24 mm PA12 housing
  • PNP normally-open output; DC three-wire connection
  • Typical 9 mm overrun distance; long-overrun configuration
  • Typical 2.8 mT response sensitivity and 0.7 mT hysteresis
  • Reproducibility ≤0.1 mT at constant supply and ambient temperature
  • 1,000 Hz switching frequency; 25 ms availability delay
  • Axial 5 m three-wire PVC cable with ferrules; 0.14 mm² conductors
  • Status LED; SW2.0 fixing screw; typical 0.4 Nm mounting torque
  • 10–30 V DC; 10 mA without load; ≤200 mA continuous output current
  • IP67/IP69K; −30 to +80 °C operation; reverse-polarity, short-circuit and power-up pulse protection

Monitor a selected cylinder-magnet position with a long-overrun PNP switching condition and connect through a 5 m three-wire PVC lead.

Technical Specification Matrix

ParameterValue
Cylinder typeT-slot
Adapter-dependent cylinder typesProfile, tie rod, round body, dovetail groove, SMC rail CDQ2 and SMC rail ECDQ2
Housing length24 mm
Switching outputPNP normally open; DC three-wire
Switching frequency1,000 Hz
Response sensitivityTypical 2.8 mT
Overrun distanceTypical 9 mm; magnet travel while the switching signal is output
HysteresisTypical 0.7 mT
Reproducibility≤0.1 mT at constant supply voltage and ambient temperature
Power supply10–30 V DC
Current consumption10 mA without load
Voltage drop≤2.2 V
Continuous output current≤200 mA
Protection classIII
Availability delay25 ms
Circuit protectionReverse-polarity, short-circuit and power-up pulse protection
ConnectionAxial 5 m three-wire PVC cable with ferrules
Conductor cross-section0.14 mm²
Cable diameterØ2.9 mm
Conductor functionsCd-001: BN=L+; BK=NO; BU=M
Housing materialPA12 plastic
MountingT-slot; fixing screw SW2.0; typical tightening torque 0.4 Nm
IndicationLocal status LED
Teach-inNone
IP ratingIP67 according to EN 60529, footnote IP67/IP68; IP69K according to DIN 40050
Operating temperature−30 to +80 °C
Shock resistance30 g, 11 ms
Vibration resistance10–55 Hz, 1 mm
EMCEN 60947-5-2
MTTFD2,289 years
DCavg0%
Mission time20 years
Sensor element position1.5 mm for the long 9 mm overrun version, as shown in drawing

Industrial Applications

1. Confirming cylinder arrival before a process step

A pneumatic transfer can place the sensor in the cylinder T-slot at its intended arrival position. External sequencing reads the PNP normally-open state and interprets its output polarity before permitting the next ordinary process action. Commissioning checks piston-magnet response, actual cylinder geometry and sensor placement against the typical response sensitivity and overrun distance.

Problem Solved

A cylinder-position condition helps external sequencing distinguish arrival from travel outside the selected sensing location, using the installed magnetic switching point as its process reference.

Cylinder arrival T-slot mounting PNP NO

2. Measuring dwell at a cylinder position

A press or handling station can hold its cylinder magnet at the monitored position during an ordinary process dwell. External timing logic measures the duration of the normally-open switching condition and compares it with the intended sequence. Setup establishes the target magnet, sensor position and input sampling so arrival and departure produce distinct usable transitions.

Problem Solved

The duration of the position condition gives external process logic a dwell reference, helping identify an unusually short or extended hold at the monitored cylinder location.

Position dwell External timing Magnetic switching

3. Monitoring cylinder cycle time from repeated position events

An external monitoring routine can timestamp repeated transitions as the cylinder returns to the same sensor position during successive cycles. It compares those intervals with its normal process timing to identify a delayed or missing return. The installation keeps sensor mounting fixed and accounts for normally-open polarity, magnetic reproducibility and connected-input sampling.

Problem Solved

Repeated position-event intervals give external monitoring a cycle-time reference, helping distinguish a delayed or missing return from the established movement pattern of the cylinder.

Cycle timing Repeated position event Return monitoring
Select your currency