| Functional principle | Photoelectric retro-reflective sensing with polarized coaxial/autocollimation optics |
| Special application | Detecting transparent objects |
| Sensing range | 0–0.55 m with P250F reflector |
| Maximum sensing range | 0–1.2 m with P250F reflector |
| Reflector minimum distance | No minimum distance with coaxial optics |
| Light source | Visible red PinPoint LED |
| Wavelength | 640 nm |
| Light spot size | Ø12 mm at 250 mm |
| LED service life | Average 100,000 h at ambient +25 °C |
| Adjustment | IO-Link |
| AutoAdapt | Yes |
| Digital output | PNP; configurable multifunction pin 2; maximum output current ≤50 mA |
| Switching mode | Light/dark switching |
| Pin assignment | 1 BN=L+; 3 BU=M; 4 BK=QL1/C; 2 WH=MF (CD-367) |
| Response time | <0.5 ms signal transit time with resistive load |
| Switching frequency | 1,000 Hz general specification; mode-specific Smart Task rates listed separately |
| Power supply | 10–30 V DC, limit values |
| Residual ripple | <5 Vpp; remain within supply tolerances |
| Current consumption | 20 mA without load |
| Circuit protection | A: supply reverse-polarity protection; B: output reverse-polarity protection; D: outputs overcurrent and short-circuit protection |
| Polarization filter | Yes |
| Housing design | Rectangular |
| Housing material | ABS/PC plastic |
| Optics material | PMMA plastic |
| Connection | 200 mm PVC cable with male M8 four-pin connector; do not bend below 0 °C |
| Conductor cross-section | 0.09 mm² |
| Cable diameter | Ø3 mm |
| Mounting provisions | Fixing holes Ø3.2 mm, drawing center axes |
| IP rating | IP67 |
| Operating temperature | −20 to +50 °C |
| Storage temperature | −40 to +75 °C |
| MTTFD | 1,987 years |
| DCavg | 0% |
| Pin 4 connection restriction | This switching output must not be connected to another output |
| Pin 2 configuration | External input; teach-in input; sender-off input; detection output; logic output; device contamination alarm output |
| Protection class | III |
| Configured pin 2 response time | 300–450 µs with resistive load; valid for switching output on pin 2 if configured with software |
| Configured pin 2 repeatability | 150 µs for switching output on pin 2 |
| Configured pin 2 frequency | 1,000 Hz at 1:1 light/dark ratio; valid for switching output on pin 2 if configured with software |
| IO-Link | V1.1; COM2 at 38.4 kBaud; compatible master port type A; SIO supported |
| IO-Link cycle time | 2.3 ms |
| IO-Link process data | 16 bits: bit 0 switching signal QL1; bit 1 switching signal QL2; bits 2–15 empty |
| IO-Link identifiers | VendorID 26; DeviceID 0x800124 / 8388900 |
| Smart Task | Base logics |
| Logic functions | Direct; AND; OR; WINDOW; hysteresis; inverter available |
| Timer functions | Deactivated; switch-on delay; off-delay; on-and-off delay; impulse (one-shot) |
| Smart Task frequency | SIO Direct: 1,000 Hz; SIO Logic: 1,000 Hz; IO-Link: 900 Hz |
| Smart Task response time | SIO Direct: 300–450 µs without IO-Link or internal logic/timing; SIO Logic: 500–600 µs using internal logic/timing and Automation Functions without IO-Link; IO-Link: 500–900 µs with communication, logic/timing and Automation Functions |
| Smart Task repeatability | SIO Direct: 150 µs; SIO Logic: 150 µs; IO-Link: 400 µs |
| Diagnostics | Device status; quality of teach; quality of run with contamination display |